AWCY E43-48-48x Full Release

The Everyman's 43x (E43, E43x, E48)

A beginners printable pistol frame

v1.0

###############################################################################

/X> Release Notes <X\

###############################################################################

Second AWCY release!

###############################################################################

/X> Credits <X\

###############################################################################

[-+ Brought to you by +-]

︻╦╤─ Sigfried(Co-developer, primary 43x/48) ─╤╦︻

︻╦╤─ 4myright(Co-developer, primary 43) ─╤╦︻

︻╦╤─ bitplumb(Head test engineer) ─╤╦︻

[-+ With the help of +-]

Engarm(ongoing auto sear development assistance),

Because2nd(OEM measurements), All4one(Early CAD help),

and v8vtwin(Moral Support)

[-+ Additional thanks to +-]

Skyraze, Karver, Soggyknee, handydandy, all_i_no_is_gloc, mr_380_EZ,

apophis9x19, [REDACTED],

and the entire Are We Cool Yet? team

###############################################################################

/X> Print Settings <X\

###############################################################################

Filament: PLA+ or stronger

Temp: 205-225 (PLA)

Frame orientation: Print magazine well down.

Infill: 99% (gyroid pattern with tree supports preferred)

###############################################################################

/X> Materials <X\

###############################################################################

1x SS80 builders kit including:

This can be gotten from glockstore.com

1x combo front rail block

1x single piece rear rail

1x 4mm trigger pin

1x 3mm rear rail pin

1x Glock 43/43x/48 parts kit including:

1x barrel

1x upper parts kit

1x lower parts kit

###############################################################################

/X> Linked Guides <X\

###############################################################################

Hans Grabber builds a Glock

###############################################################################

/X> Assembly <X\

###############################################################################

[-+ Frame +-]

1. Remove supports, taking care to clean out the sear pocket.

2. Check that all rails and pins fit. Ream out holes if required.

3. Install mag catch spring and mag catch.

4. Install the rear rail.

5. Install sear housing and trigger. Make sure all holes align

properly with the frame.

6. Install the last round hold open lever.

7. Place the front rail into the frame.

8. Drive the 4mm pin through the front rail, last round hold open, and

trigger. (It can help to align these three components with a

smaller pin before driving through the 4mm pin.)

9. Drive the 3mm pin through the rear rails and sear housing.

10. Install the takedown bar and spring in front of the combo rail.

11. Install a the slide, and rack the slide numerous times to ensure

function and ensure the rails are firmly seated.

12. So anyway, get to blasting.

###############################################################################

/X> Statistics <X\

###############################################################################

Combined round count from beta: 2195

Max round count on one frame: 600 (4myright)

Max round count with different materials:

Nylonx: 600 and counting

Resin: 300 and counting

PLA+: 215 and counting

(give us a break theres an ammo shortage)

###############################################################################

/X> Troubleshooting <X\

###############################################################################

Issue: Slide does not rack cleanly, or hangs up on the front of the

frame.

Solution: The SS80 rails have notoriously bad QC. Check your rails for

flatness and squareness. If that does not resolve the issue, check the

frame for warp. Even the slightest warp in the sear will result in

difficultly cycling.

Issue: Mag catch does not allow the removal of OEM mags.

Solution: Make sure you have printed the OEM mag catch, not the shield

mag catch. The printed Shield catch has a larger contact area to insure

retention and is not OEM compatable.

Issue: I have assembled the pistol and am not cool yet.

Solution: Being cool is about the journey, not the destination.

###############################################################################

-`-,-{@ AWCY? - Stronger Together @}-,-`-

(oven appreciation group)

Join us at: https://www.AreWeCoolYet.WTF

###############################################################################

Gomagnet 2023.

Streaming while downloading with WebTorrent.

The data comes from Pirate Bay.

The Everyman's 43x (E43, E43x, E48)

A beginners printable pistol frame

v1.0

/X> Release Notes <X\

Second AWCY release!

/X> Credits <X\

[-+ Brought to you by +-]

︻╦╤─ Sigfried(Co-developer, primary 43x/48) ─╤╦︻

︻╦╤─ 4myright(Co-developer, primary 43) ─╤╦︻

︻╦╤─ bitplumb(Head test engineer) ─╤╦︻

[-+ With the help of +-]

Engarm(ongoing auto sear development assistance),

Because2nd(OEM measurements), All4one(Early CAD help),

and v8vtwin(Moral Support)

[-+ Additional thanks to +-]

Skyraze, Karver, Soggyknee, handydandy, all_i_no_is_gloc, mr_380_EZ,

apophis9x19, [REDACTED],

and the entire Are We Cool Yet? team

/X> Print Settings <X\

Filament: PLA+ or stronger

Temp: 205-225 (PLA)

Frame orientation: Print magazine well down.

Infill: 99% (gyroid pattern with tree supports preferred)

/X> Materials <X\

1x SS80 builders kit including:

This can be gotten from glockstore.com

1x combo front rail block

1x single piece rear rail

1x 4mm trigger pin

1x 3mm rear rail pin

1x Glock 43/43x/48 parts kit including:

1x barrel

1x upper parts kit

1x lower parts kit

/X> Linked Guides <X\

Hans Grabber builds a Glock

/X> Assembly <X\

[-+ Frame +-]

1. Remove supports, taking care to clean out the sear pocket.

2. Check that all rails and pins fit. Ream out holes if required.

3. Install mag catch spring and mag catch.

4. Install the rear rail.

5. Install sear housing and trigger. Make sure all holes align

properly with the frame.

6. Install the last round hold open lever.

7. Place the front rail into the frame.

8. Drive the 4mm pin through the front rail, last round hold open, and

trigger. (It can help to align these three components with a

smaller pin before driving through the 4mm pin.)

9. Drive the 3mm pin through the rear rails and sear housing.

10. Install the takedown bar and spring in front of the combo rail.

11. Install a the slide, and rack the slide numerous times to ensure

function and ensure the rails are firmly seated.

12. So anyway, get to blasting.

/X> Statistics <X\

Combined round count from beta: 2195

Max round count on one frame: 600 (4myright)

Max round count with different materials:

Nylonx: 600 and counting

Resin: 300 and counting

PLA+: 215 and counting

(give us a break theres an ammo shortage)

/X> Troubleshooting <X\

Issue: Slide does not rack cleanly, or hangs up on the front of the

frame.

Solution: The SS80 rails have notoriously bad QC. Check your rails for

flatness and squareness. If that does not resolve the issue, check the

frame for warp. Even the slightest warp in the sear will result in

difficultly cycling.

Issue: Mag catch does not allow the removal of OEM mags.

Solution: Make sure you have printed the OEM mag catch, not the shield

mag catch. The printed Shield catch has a larger contact area to insure

retention and is not OEM compatable.

Issue: I have assembled the pistol and am not cool yet.

Solution: Being cool is about the journey, not the destination.

--,-{@ AWCY? - Stronger Together @}-,--

(oven appreciation group)

Join us at: https://www.AreWeCoolYet.WTF

-`-,-{@ AWCY? - Stronger Together @}-,-`-